Skip to content
Home » Ben & Jerry's » How To Repair a Sliding Door (DIY)

How To Repair a Sliding Door (DIY)

DIY sliding door repair may be necessary at some point. You have a chance of restoring your door, without hiring any external help. It is best to contact a glass door repair company, but if this is not possible, here is a comprehensive guide for DIY sliding door repairs.

Tools to Use

  • Screwdriver
  • Allen wrench
  • Drill
  • Pry bar
  • Rags
  • Screen roller
  • Utility knife

Materials

  • A replacement screen door
  • Replacement roller
  • Silicone lubricant

Sliding Door Repair: Step-by-step Guide

Step 1: Tune-up a Balky Sliding Door: Roller Adjustment

Take out the screen door.

Close the door all the way, with no gaps.

Determine if some rollers are not turning freely or that have fallen off. Also, if the rollers are securely attached to the track by rotating it manually.

Did you find any of these faults? Use a corded drill and screwdriver bits to remove your old rollers.

Fit in a new roller by following these instructions:

  1. Insert rollers on tracks until it locks into place. Make sure they are secure and no gaps are between its end and what’s known as a clip track.
  2. Finally, press down on it to ensure that it is locked into place.

Step 2: Stop Molding Removal

Remove screws and scrape off any pain. Test the door to establish if it is gliding smoothly. If still stuck, you will need to remove the entire door. This allows you to inspect rollers for any damages.

Please note that the sliding door is quite heavy and as such, it is best to get assistance when removing it. The door will come off without a problem for sliding door repair with the stop molding off.

Step 3:Sliding Door Removal

When removing your door, grab the edges safely so as to be able to take it out of the tracks. Place the door on an ideal surface, check all the components, including the rollers.

Step 4: Roller Replacement

Replacing rollers is a critical task. Exercise some caution when doing this so as not to damage the door further. Before any task, check the rollers for dirt or grease. Check for any cracks or missing parts. Inspect the installation of the rollers to determine if they need to be tightened.

Clean and lubricate all worn-out and dirty parts.

Do not tighten any bolts unless you have to replace a roller, as doing so could damage them. Report broken hardware immediately. Replace it with top-quality hardware.

Step 5: Replacing Door Rollers

A good number of manufacturers sell new rollers. These can be used for sliding door repair. When shopping, find a roller that matches your model.

Get the required tools and carefully remove the old rollers following the instructions from the manufacturers.

After years, the accumulated grease, dirt, and other debris may cause sliding doors to get stuck and not glode smoothly.

Cleaning: Scrub all tracks using a high-quality degreaser. Clean your rollers as well, then wipe them dry.

Stainless steel rollers: These do not corrode easily but you have to be careful when cleaning them as they are harder than most materials.

Seasoning: This is compulsory for wooden tracks and advisable for vinyl tracks. Follow the manufacturer’s guidelines carefully.

Lubricating: Apply a thin coat of silicone, then wipe it off thoroughly after allowing it to settle into the track for a few minutes. It is highly recommended that you do this outdoors where there is little wind and on a bright and sunny day as test runs indicate that less grease gets blown around under such conditions.

Step 6: Replacing the Balky Glass Sliding Door

Carefully slide the door back into place and secure it with screws. Make sure that you do not over-tighten them as doing so would only damage the rollers.

Thereafter, install stop moldings and fasten them to the track with screws. Drive these screws carefully as they need to be tight enough to prevent wear and loosening.

Apply a coat of varnish over the screw heads to ensure that they do not rust in the future and cause you to spend more money on sliding door repair.

Step 7: Test Runs

Open and close the door carefully after you apply lubrication but before implementing any repairs, as such testing will enable you to make sure that everything is working properly and there are no major adjustments needed.

DIY sliding door repair is easy using the steps of the door removal, repairing rollers, and more to accomplish this task. Ensure that you keep your tools ready and follow manufacturer guidelines to complete this job successfully.

Sliding glass doors are convenient since they allow natural light into a room without compromising on security, but if not handled carefully can be a source of accidents.

If you have pets, you can order for sliding door with a pet-safe fabric. You can also get a sliding glass door that is child-proof.

Investing in quality hardware and rollers to replace worn-out ones will increase the safety of your home. You can now complete sliding door repair by yourself.

Categories: Life

Top